Strength of this fastener is derived from the compression of the plates, mounted above and below the belt, with high tensile strength bolts. this “compression” distributes the splice tension across the full width of each fastener plate. The holding ability is, thereby, increased by not solely relying upon the bolts to resist pull-out.

Additional strength and resistance to pull-out is obtained from the specially formed teeth on each plate. These teeth imbed deep into the belt carcass, but without damaging the carcass fibers.

A tight butt splice is achieved through the exaggerated bolt hole spacing in the templet which forces the belt ends together. And, the Bolt Solid Plate Fasteners permit natural conformance with troughing or transition idlers.

The 140, 190 and 2 ¼ size fasteners are specifically designed for today’s thinner belting, allowing increased compression, greater reach-back and more fastener plates per belt width.

Bolt Solid Plate Fastener Selection Chart

wdt_ID Fastener # Belt PIW Rating (Up to) Thickness Range Recommended Minimum Pulley Diameter (90º Splice) Operating Tension: 75-100% of Belt Rating Recommended Minimum Pulley Diameter (90º Splice) Operating Tension: 50-75% of Belt Rating Recommended Minimum Pulley Diameter (90º Splice) Operating Tension: Under 50% of Belt Rating
1 1 160 3/16 to 7/16" 12" 10" 8"
2 140 225 3/16 to 7/16" 14" 12" 10"
3 190 330 5/16 to 9/16" 18" 16" 14"
4 1/1/02 300 7/16 to 11/16" 18" 16" 14"
5 2 440 9/16 to 13/16" 30" 28" 24"
6 2/1/04 620 9/16 to 1-3/16" 36" 34" 34"
7 2/1/02 450 3/4 to 1" 42" 42" 42"
8 3 560 15/16" & Over 48" 48" 48"
9 SP6 150 1/4 to 1/2" 14" 12" 10"

Fastener Metals

Bolt Solid Plate fasteners come in a variety of metals for many applications.

Bolt Solid Plate Fastner System

Steel

Stainless Steel

Everdur

Megalloy

Monel

Promal

Rubber-Covered Steel

Fasteners Required for Various Belt Widths

wdt_ID Belt Widths Fastener #s 1, 140, 190 90º Splice Fastener #s 1, 140, 190 45º Splice Fastener #s 1 ½, 2, 2 ¼, SP6 90º Splice Fastener #s 1 ½, 2, 2 ¼, SP6 45º Splice Fastener #s 2 ½, 3 90º Splice Fastener #s 2 ½, 3 45º Splice
1 12" 10 12 8 9 6 7
2 18" 15 19 12 15 9 12
3 24" 20 26 16 21 13 17
4 30" 25 33 20 27 16 21
5 36" 30 41 24 33 19 26
6 42" 35 48 28 39 22 31
7 48" 40 55 32 44 26 35
8 54" 45 63 36 48 29 40
9 60" 50 69 40 56 32 44
10 72" 60 83 48 68 39 53

Ordering Information

“E” Box Fastener Sets

One “E” box contains 25 complete fastener sets. A set consists of a top plate, a bottom plate, two nuts, two bolts and an assembly clip. The steel and Megalloy fasteners are available in 100 set containers. To order these containers, substitute a “C” for the first “E” in the part numbers below.

"E" Box Ordering Numbers

wdt_ID Metal Order Number Order Number Order Number Order Number Order Number Order Number Order Number Order Number
11 Steel 1E 140E 190E 1 ½E 2E 2 ¼E 2 ½E (10/Box) 3E (10/Box)
12 Stainless Steel 1ES 140ES 190ES 1 ½ES 2ES 2 ¼ES SP6ES
13 Stainless Top Plates (Balance Steel) 1EST 140EST 190EST 1 ¼EST 1 ½EST 2EST
14 Monel 1 ½EM 2EM
15 Monel Top Plates (Balance Steel) 1EMT 1 ½EMT 2EMT
16 Everdur 1EE 140EE 190EE 1 ½EE 2EE 2 ¼EE
17 Megalloy Top Plates (Balance Steel) 140EMA 190EMA 1 ½EMA 2EMA 2 ¼EMA SP6EMA
18 Megalloy Top & Bottom Plates (Steel Nuts & Bolts 140EMAP 190EMAP 1 ½EMAP 2EMAP
19 Promal Top Plates (Balance Steel) 140EP 1 ½EP 2EP
20 Rubber Covered Top Plates (Balance Steel) 190ERCT 1 ½ERCT 2ERCT 2 ¼ERCT

 

Extra Bolts or Nuts

wdt_ID Metal 1 140 190 1 ½ 2 & RP2 2 ¼ 2 ½ & 3 RP1 & SP6
1 Steel 20391 20395 20399 20402 20406 20410 20414 20398
2 Stainless Steel 20392 20396 20400 20403 20407 20411 - 20396
3 Monel - - - 20404 20408 20416 -
4 Everdur 20394 20397 20401 20405 20409 20412 20417 20397
5 Extra Nuts Ordering Numbers (100/Box)
6 Steel 20377 20378 20379 20377
7 Stainless Steel 20381 20382 - 20381
8 Monel - 20385 20386 -
9 Everdur 20387 20388 20389 20387

Bolt Solid Plate Installation Tools & Supplies

The only tools needed for installing Solid Plate fasteners are a templet and simple, portable hand tools. Impact wrench driven power tools are suggested since they can speed installation time by as much as 50%.

Templets

Templets insure precise hole placement for a tight splice. Templets install one size fastener only. Templets are not interchangeable among fastener sizes, but certain templet widths of a given size may be interchanged in an emergency.

90 º Templets

wdt_ID Belt Width For #1 For #140 For #190 For #1 ½ For #2 For #2 ¼ For #2 ½ For #3 For #SP6
1 12" 1-12 140-12 - - - - - - -
2 18" 1-18 140-18 190-18 1 ½-18 - - - - -
3 20" 1-20 140-20 - 1 ½-20 - - - - -
4 24" 1-24 140-24 190-24 1 ½-24 2-24 - 2 ½-24 - SP6-24
5 26" - - 190-26 - - - - - -
6 28" - - 190-28 - - - - - -
7 30" 1-30 140-30 190-30 1 ½-30 2-30 - 2 ½-30 - -
8 36" 1-36 140-36 190-36 1 ½-36 2-36 2 ¼-36 2 ½-36 - -
9 42" 1-42 140-42 190-42 1 ½-42 2-42 2 ¼-42 2 ½-42 - -
10 48" 1-48 140-48 190-48 1 ½-48 2-48 2 ¼-48 2 ½-48 3-48 -
11 54" - - - 1 ½-54 - - - - -
12 60" - - - 1 ½-60 2-60 2 ¼-60 - 3-60 -

Note: A 45186º splice requires a special templet. Please call for information.

Hand or Power Tools for Bolt Solid Plate Fasteners

In addition to a templet, the following hand or power tools are required for installation: a punch or a boring bit (the punch is preferred for general use and where the belt cover is over 3/16″ thick); a wrench; and two bolt breakers.

A power impact wrench cuts application time by approximately 50%. It should be used with a “quick change chuck” which adapts the tools to the square drive stud on an air or electric impact wrench.

Hand & Power Tools for Bolt Solid Plate Fasteners

wdt_ID Fastener Number Bolt Hole Diameter Punch Part # Boring Bit Part # Wrench Part # Bolt Breaker Part #
1 Hand Tool Ordering Numbers
2 1, 140, 190, SP6 1/4" P1P B1B S1S 110
3 1 ½, 2, 2 ¼ 5/16" P2P B2B S2S 112
4 2 ½, 3 3/8" P3P B3B S3S 113
5 Power Tool Ordering Numbers
6 1, 140, 190, SP6 1/4" HP1 HB1 HW1 Order as Above
7 1 ½, 2, 2 ¼ 5/16" HP2 HB2 HW2
8 2 ½ 3 3/8" HP3 HB3 HW3

Quick Change Chuck

To use power tools, a Quick Change Chuck is required. This adapts tools to the square drive stud on air or electric impact wrenches.

Quick Change Chuck for Bolt Hinged Fasteners

wdt_ID Drive Size Part #
1 1/2" 5552